A worn finish without deep damage
What's behind it: The top coat has worn thin but the wood underneath is still fine.
What we check first: Whether a screen-and-recoat will do, which avoids a full sanding.
You see the plan and the number before a single tool comes out. Free Quotes, no pressure.
Questions Welcome
A call is the quickest way to describe it, and there's nothing to sign.

No obligation
Call (413) 347-4859How this works
We refinish hardwood floors in Pittsfield. What a job costs depends mostly on how much wood the floor has left to sand, so we look at the floor before we talk numbers. This page is the overview, and the pages it points to go deeper on each kind of job.
We'll talk it through with you, but here's where each one fits.
Three things move the price: the species of wood, the finish that's on it now, and how much wear layer is left. A floor in decent shape that only needs a light refresh costs less than one that needs a full sand, because there is less wood to cut and less finish to strip.
Square footage alone doesn't tell us what's under the finish, and the condition of the floor moves the price more than the size of the room does. Tell us what you have when you call and we'll say what we can. The exact number is confirmed once we've seen the floor.
Before we agree to a full sand, we check the species, the existing finish, and how much wear layer remains. A floor with plenty of wood left can take a full sand and come out looking new. A floor that has been sanded hard before may not, and then the straight answer is a lighter approach or a different repair.
When a full sand is the right call, we rough-cut the field with a coarse grit to strip the old finish, then step up through medium and fine grits so the surface is smooth before any finish goes on. After that comes the finish, and then the cure. How long you stay off the floor depends on the wood and the finish we pick together.
If you already have a finish in mind, tell us. Whether it suits your floor depends on the wood, how the room gets used, and what's on the boards today, and we'll tell you plainly if it's a poor fit.
Half the houses in Pittsfield went up in 1950 or earlier, so a lot of the floors we see are seventy-odd years old. A floor that has been walked on and refinished that many times may have less wood left than it looks like, and it may carry layers of old finish that have to come off before anything new goes down.
So we don't assume. A floor in a house from that era might be in good shape under a tired finish, or it might be worn thinner than you'd guess from standing on it. We would rather find that out at the start than halfway through a sand.
Refinishing a floor is generally not permit work. Massachusetts currently uses the 10th Edition of its state building code, residential provisions included, and any larger floor work falls under that edition.
If the job grows past refinishing, say you're pulling up flooring as part of a bathroom remodel or changing the floor structure, check with the Building Department before work starts.
If you want the sanding done with dust control in mind, start with our dustless sanding page. If the floor only needs a fresh topcoat, the screen and recoat page covers that. Color changes and stain choices are on the staining page. Boards that are cupped, cracked or stained through have their own page on board repair, and if you're putting hardwood where there isn't any now, read the installation page.
Not sure which one you need? Tell us the age of the house and what the floor looks like now, and we'll tell you which page, and which kind of visit, fits.
Find the job that sounds like yours and start there.
What it usually means, and what we check before recommending anything.
What's behind it: The top coat has worn thin but the wood underneath is still fine.
What we check first: Whether a screen-and-recoat will do, which avoids a full sanding.
What's behind it: Moisture from below or a past leak has made the boards curl at the edges.
What we check first: Moisture readings and the source, before any sanding.
What's behind it: Pet stains, water damage or broken boards that sanding won't fix.
What we check first: Which boards need replacing and how to weave new ones in.
What's behind it: A full sand takes the floor back to bare wood, ready for a new stain.
What we check first: The wood species, since some take stain more evenly than others.
Each request follows the same few steps:
Describe the job and your timing, and we'll give you an honest read, not a sales pitch.
We size up the work in person so the quote is real, not a guess.
The scope, the timeline, and the price go on paper, and nothing starts until you've read it.
The work gets done and checked, and the site is left clean.
We cover Pittsfield, MA and nearby communities including Lenox, Lee, Adams. Call (413) 347-4859 if you're not sure we reach you.
We cover 4 communities.
ZIP codes: 01201.
These ranges are a starting point for planning, and yours gets its own written price once we've seen it.
$1.15–$3.50 per sq. ft.
$7–$14 per sq. ft.
$45–$175 per board
No obligation
Call (413) 347-4859How this works
A full sand-and-refinish is a once-a-decade-or-more event for most homes, over-sanding shortens a floor's life. A screen-and-recoat every few years in high-traffic homes refreshes the finish and delays the day a full refinish is needed, which is the cheaper way to protect the wood.
Surface scratches and gray sand right out. Deep gouges and dark pet stains that have soaked into the wood are the hard cases, sanding removes what it can, stubborn stains may need board replacement, and we're upfront about which marks will fully disappear and which will only fade.
It comes down to wear-layer thickness. Solid hardwood can usually be sanded several times over its life; most engineered floors can take one light refinish if the veneer is thick enough. If boards are cupped past flat, sanded down to the tongue, or water-blackened through, replacement of those boards is the honest call, we check before quoting a full sand.
A full refinish sands back to bare wood and rebuilds the finish, it removes deep scratches, gray, and lets you change color. A screen-and-recoat lightly abrades the existing finish and adds one fresh coat; it's far cheaper and faster but only works while the old finish is intact and the wear hasn't reached the wood.
Far less than the old reputation if it's done right. We run a dust-containment system that pulls fines off the sander as it cuts, and we seal off the rest of the house. You'll still want to wipe surfaces after, but it's nothing like the whole-house film sanding used to leave.
Oil-based ambers the wood, adds warmth, and is very durable but cures slowly and smells strong. Waterborne dries clear, keeps the wood's natural tone, has low odor, and cures faster so you're back on the floor sooner. Both are durable now; the choice is mostly color, smell, and how fast you need the room back.
With waterborne finish you can usually walk in socks the next day and return light furniture in a couple of days. Oil-based needs longer. Either way the finish keeps hardening for a couple of weeks, so we advise waiting on rugs and heavy furniture until it has fully cured.
Yes, once the floor is sanded to bare wood we can stain it lighter or darker before the finish coats. Some species take stain more evenly than others; we always test the stain on your actual floor in an out-of-the-way spot so you approve the real color, not a sample board.
A call is the quickest way to describe it, no obligation.